Technical News
Find what you need fast and easily
July 2022
7/18/2022
- Sash machinings for S70710 & S70776 sashes for butt joint connection added on the chapter of milling-tooling operations page 240
7/18/2022
- No head metric screw 798-83-305-06 added for the connection of the add-on profile S77005 with the frame of the system
7/8/2022
- The chapter of glazings has been updated
7/8/2022
- Frame S77149 added on the index and profile 1:1 chapters
7/8/2022
- Cutting of water dripper width has been corrected (the correct one is 90 degrees)
7/1/2022
- Sash gasket 250-77-918-03 (hidden sash - short frame) replaced by 250-77-918-13 for optimal operation.
7/1/2022
- Butt joint Pivot have been temporarily removed from the technical catalogue to avoid errors. New update will be provided when the system is complete after the accessories will have been redesigned.
7/1/2022
- Glazing gasket 200-06-860-01 for 24mm glazing added in the sashes M19622 and M19626 of M9660 phos
7/1/2022
- Redesign and new solution of the rotation pin for motorized louvre 720-05-600-00, reducing the noise produced during operation
7/1/2022
- Inside stiffener profiles S70807 & S70832 have been added on index and profiles 1:1 chapters. They also have been added in the chapter of sash dimension constraints.
June 2022
6/22/2022
- Accessory code 851-19-622-00 (Crimping knife for M9660 Phos unijet) has been added on the chapter of accessories as well as in the machining for crimp corner cleats for the sash M19622.
6/22/2022
- Accessory 8300000200 (“U” shape block only for single membrane) has been modified and criteria of the suitable accessory for the cases of single or quadruple membrane have been defined.
- Check / redefinition of the anchors used for the support of M8200 base profiles.
6/22/2022
- Dimensions for sash mashining S70714 with S70710 and S70714 with S70706 for butt joint connection have been corrected
6/10/2022
- The distance of the center of the handle machining for sash M4542 is corrected for lift & slide typologies
6/10/2022
- Milling tools added on page 31,32,33.
- Millings tooling operation for corner sashes added on page 60,61.
- Page 36 and 37 of Meeting stile locking machinings have been replaced. Adjustable locking with meeting stile also added on those pages code 6406513000.
6/10/2022
- Four mushroom pins for the side locking points (3 set + 1piece), in order to align them with the lock of the sashes added on the chapter of accessories and on the cutting lists:
- 6406512000 ADJUSTABLE SET OF ADDITIONAL LOCKING POINTS FOR PARALLEL SLIDING S650.
- 6406513000 ADJUSTABLE LOCKING SET FOR S650 WITH MEETING STILE.
- 6403162413 ADJUSTABLE SET OF ADDITIONAL LOCKING POINTS FOR CORNER S650.
- 6406502000 ADJUSTABLE MUSHROOM-SHAPED PIN S650 FOR REPLACEMENTS.
6/10/2022
- Meeting stile locking machinings on page 37 have been replaced. Adjustable locking with meeting stile also added on this page code 6406513000.
- Milling tools added on page 62.
6/10/2022
- Four mushroom pins for the side locking points (3 set + 1piece), in order to align them with the lock of the sashes added on the chapter of accessories and on the cutting lists:
- 6406512000 ADJUSTABLE SET OF ADDITIONAL LOCKING POINTS FOR PARALLEL SLIDING S650.
- 6406513000 ADJUSTABLE LOCKING SET FOR S650 WITH MEETING STILE.
- 6403162413 ADJUSTABLE SET OF ADDITIONAL LOCKING POINTS FOR CORNER S650.
- 6406502000 ADJUSTABLE MUSHROOM-SHAPED PIN S650 FOR REPLACEMENTS.