Technical News
Find what you need fast and easily
June 2022
6/22/2022
- Accessory code 851-19-622-00 (Crimping knife for M9660 Phos unijet) has been added on the chapter of accessories as well as in the machining for crimp corner cleats for the sash M19622.
6/22/2022
- Accessory 8300000200 (“U” shape block only for single membrane) has been modified and criteria of the suitable accessory for the cases of single or quadruple membrane have been defined.
- Check / redefinition of the anchors used for the support of M8200 base profiles.
6/22/2022
- Dimensions for sash mashining S70714 with S70710 and S70714 with S70706 for butt joint connection have been corrected
6/10/2022
- The distance of the center of the handle machining for sash M4542 is corrected for lift & slide typologies
6/10/2022
- Milling tools added on page 31,32,33.
- Millings tooling operation for corner sashes added on page 60,61.
- Page 36 and 37 of Meeting stile locking machinings have been replaced. Adjustable locking with meeting stile also added on those pages code 6406513000.
6/10/2022
- Four mushroom pins for the side locking points (3 set + 1piece), in order to align them with the lock of the sashes added on the chapter of accessories and on the cutting lists:
- 6406512000 ADJUSTABLE SET OF ADDITIONAL LOCKING POINTS FOR PARALLEL SLIDING S650.
- 6406513000 ADJUSTABLE LOCKING SET FOR S650 WITH MEETING STILE.
- 6403162413 ADJUSTABLE SET OF ADDITIONAL LOCKING POINTS FOR CORNER S650.
- 6406502000 ADJUSTABLE MUSHROOM-SHAPED PIN S650 FOR REPLACEMENTS.
6/10/2022
- Meeting stile locking machinings on page 37 have been replaced. Adjustable locking with meeting stile also added on this page code 6406513000.
- Milling tools added on page 62.
6/10/2022
- Four mushroom pins for the side locking points (3 set + 1piece), in order to align them with the lock of the sashes added on the chapter of accessories and on the cutting lists:
- 6406512000 ADJUSTABLE SET OF ADDITIONAL LOCKING POINTS FOR PARALLEL SLIDING S650.
- 6406513000 ADJUSTABLE LOCKING SET FOR S650 WITH MEETING STILE.
- 6403162413 ADJUSTABLE SET OF ADDITIONAL LOCKING POINTS FOR CORNER S650.
- 6406502000 ADJUSTABLE MUSHROOM-SHAPED PIN S650 FOR REPLACEMENTS.
6/10/2022
- Μachining for hook profile for narrow fly-screen sash has been corrected.
6/10/2022
- Μachining for hook profile for narrow fly-screen sash has been corrected.
6/10/2022
- Glazing gaskets 200-08-00X-01 have been replaced with 200-09-00X-01 in all catalogue.
6/10/2022
- Maximum door dimensions per system have been corrected.
6/10/2022
- New typologies No5 (1 panel door) and No6 (2 leaf door) added on the chapter of typologies cutting lists.
- Glazing bridge 290-65-104-00 added on the chapters of accessories, cutting lists, sections and glazings.
6/2/2022
- Gasket for hook profile 240-00-462-01 has been replaced by 240-00-563-00 in all typologies with narrow hook profile and in all pocket typologies due to the difficulty of installation. For the rest typologies, the gasket remains the same.
- Glazing gaskets 200-08-00X-01 have been replaced with 200-09-00X-01 in all catalogue.
6/2/2022
- Gasket for hook profile 240-00-462-01 has been replaced by 240-00-563-00 in all typologies with narrow hook profile and in all pocket typologies due to the difficulty of installation. For the rest typologies, the gasket remains the same.
- Glazing gaskets 200-08-00X-01 have been replaced with 200-09-00X-01 in all catalogue.
6/2/2022
- Threshold M9403 added on profile 1:1 and on profile index.
6/2/2022
- Sections of P150 updated.
- Rectangle tube profile S-20x10x1,5 added on the chapter of profiles.
- Profiles S-30x30x1,3 & Γ-30x30x1,5 have been deleted from the chapter of profiles.
6/2/2022
- Glazing bridges have been added in the chapter of milling-tooling operations.
- Codes 720-35-001-00 & 720-35-002-00 have been removed and replaced by 720-35-006-00 & 720-35-007-00 respectively due to technical improvement.
May 2022
5/27/2022
- Replacement of frame adjusting profile to further reduce installation time.
- Profile S85014 is replaced with S85054, and S85028 is replaced with S85056. The frame adjuster accessory 424-85-014-01 is no longer needed.
- New screws are needed (798-83-308-16 & 798-21-448-32) which are presented in the relative catalogue sections (i.e. accessory cuttings and milling-tooling operation) with the adjusting profile installation for profiles S85054 and S85056 (p. 205).
- Glazing gaskets 200-08-00X-01 have been replaced with 200-09-00X-01.
- Moment of inertia Ix updated in all thermal break profiles. The measurement is per meter (<1,5 <2,0 <2,5 <3,0 <3,5 >3,5) and Ιx is calculated in compliance with EN 14024.