Technical News
Find what you need fast and easily
November 2022
11/23/2022
- Codes for crimping knives and punching presses for crimp corner cleats and nail corner cleats for hidden sashes added on the pages 284-285.
- Plastic subsills 312-67-51-03 & 312-67-000-03 have been added on chapter of accessories and on the chapter of assembly page 324.
- End cap 310-67-271-03 for double sash door, with rubber seal without threshold have been added on chapter of accessories and on the chapter of assembly page 305.
- Glazing list for Epdm pages 336-337 regarding inner gaskets 200-09-00X-01 have been corrected.
11/10/2022
- New accessories added on the chapter of accessories
- Screws have been corrected in page 234
- Catalogue updated with new logos, captions and cover
11/10/2022
- Drainage plan for 2-sash parallel sliding window (right typology) has been corrected
11/10/2022
- Dimension has been corrected on Low threshold installation - Outwards Opening
11/10/2022
- Plastic Transom Cleat 160-67-908-03 has been added on the chapter of accessories and its installation on page 322
11/10/2022
- Max widths under condition have been added in the slats 303029, 303024, 303015, 303026, 303030
11/10/2022
- New Section P100 Slim with single glass 10mm has been added on page 38 of the catalogue
- In system P100 Slim the seal gasket used is 220-60-002-01
October 2022
10/27/2022
- Profiles 1:1 have been updated
- 3a typology has been updated Single sash OUTTER lift & slide with fixed panes only in design
- Corrections have been made with regards to typology 18 Double sash meeting stile pocket & slide window with fly-screen and shutter
- The correct shutter sash is M14386, not S364 and the correct cutting for the shutter invertion height M14245 is Wsu=Suh-41
10/27/2022
- 4 profiles added on the chapter of profiles: Transom profile S67162, cover profile M35209, pressure plate profile Μ35008, add-on profile S67166
- The alternative solution of the transom profile S67162 added on page 57 and its installation on sash and on "T" profile added on the chapter of milling-tooling operation
- Insulating bar for curtain walls code 720-10-600-00 and curtain wall gasket transom code 230-10-911-03 added on the chapter of accessories
- Dimensional Limitations chapter has been updated. The diagrams are calculated in compliance with EN 14024
10/27/2022
- No of pieces of the alignment corner 180-20-040-00 have been corrected in typology 4 (Double Sash tilt & turn window)
- The design of the sash M19702 has been changed in all catalogue
10/27/2022
- 2 add-on profiles Μ65152 & Μ65154 have been added on the chapter of profiles. M65152 creates extra space for thicker plaster application on the two sides, whereas M65154 allows trickle vent installation.
- Quantities of 310-65-137-00 rod reinforcement have been corrected in 3+1 4panels folding door
- Quantities of 360-65-103-xx door hinge have been corrected in two panels door
10/27/2022
- The sliding roller 6001450000 added on typology PS6.
- Cuttings of pvc hardware spacer 6604542103 have been corrected in Lift and slide typologies from H-93 to H-128. The cutting also of the one side is 90deg and on the other side is 45deg.
10/27/2022
- The new lift & slide solution of SUPREME S700!
September 2022
9/26/2022
- Dimension of Frame adjuster installation has been corrected.
- Dimension perforation of Milling for Middle Handle 380-85-012-XX.
- Dimension perforation of Milling for cylinder 35-10-35 (40/40) EX-460-34-040-00 has been corrected
9/26/2022
- New typology No7 One sash window with fixed panel - outwards opening has been added
9/13/2022
- Cutting of Interlock PVC code 6604405000 has been corrected in typology PS7 in H-50.8
9/13/2022
- Sash M65146 added on the chapter of profiles, typologies sections and on the chapter of milling-tooling operation regarding the corner cleats of the sash and its installation.
- The chapter of accessories has been updated
August 2022
8/29/2022
- Draining machinings have been corrected on the tracks from 11,4mm to 12mm
8/2/2022
- Add-on profile S67905 added on the chapter of profiles