Technical News

• Added profiles, that correspond to the glazing list table

• Certificate DIN 18008-4 (ApB), which is very useful for the markets of Germany, Switzerland and Austria, is added on page 7.

• Dimensional limitation updated.
• The calculation of the static diagrams is now made according to EN 14024

• Four new typologies (no 4, no 6, no 9, no 12) with the new threshold S11536 and the additional profiles S11537 & S70773 added on the technical catalogue. Τhose profiles also added in the profiles chapter
• Accessories that added to the technical catalogue: 210-11-536-03 (Central Gasket for SD115 Threshold), 250-11-514-03 (Frame gasket SD115), 250-11-516-03 (Frame gasket SD115) & 310-11-536-00 (Threshold connection cap)
• Central gasket 220-10-003-03 was replaced with the central gasket 250-11-514-03 in all typologies.
• Central gasket 220-10-004-03 was replaced with 250-11-516-03 in vent-frame head condition.

• Τ-profile M19874 added on the profiles 1:1. This profile is suitable with M19716 frame

• Profiles M5657 Louvre & M9010 cap added on the profiles index and profiles 1:1 chapters. The section is on page 43.

• Dimensional limitation updated. The calculation of the static diagrams is now made according to EN 14024

• Primary & secondary sash sizing dimension for doors added on general milling tooling operations chapter
  

• New automations added on the accessories chapter.

• Dimensional limitation updated. The calculation of the static diagrams is now made according to EN 14024
• Add-on profiles S67964 & S67048 added on the profile index & profile 1:1 chapters

• Catalogue updated with gutter and subsills
• The correct S35019 trimming was replaced in the sections of the pocket typologies and the profile cuttings for the widths for sashes, flyscreen sashes and shutters were corrected.

• Seal for anchor 290ml transparent code 770-54-662-00 added on the chapter of accessories.
• The application of 770-54-662-00 added on the chapter of instructions page 78.

• Dimensional limitation updated. The calculation of the static diagrams is now made according to EN 14024. 

• 3 typologies added: No 3 Four-Sash with meeting stile, No 4 Four-Sash with meeting stile and fixed and No 5 2+2 sash sliding window with 90° inner corner meeting stile.
• Profile S31735 (Reinforced sash) added on profile index and profiles 1:1.
• Dimensional limitation chapter updated.
• Accessory 311-31-620-03 (Set of end caps for corner typology) added on the chapter of accessories.
• Electric Kits for all typologies added on the chapter of accessories.

• Maximum Dimensions of M19626 added on all typologies of M9660 phos
• Milling tool for Hidden Sash code 852-19-634-00 added on the chapter of accessories

Τechnical characteristics updated:

• Glazing up to 44mm, Thermal insulation Uf = from 1,9 to 3,2 W/m2K
• Accessories added on the chapter of accessories: 380-05-000-ΧΧ (door handle with rosette), 450-49-450-00 (door lock 3-point 45/85/24/3) & 440-00-450-00 (single point latch lock 45/85/22/3).

• Additional profile S67115 (water drip) added on profile index & profiles 1:1
• Accessory code 310-67-115-03 (hidden sash pair caps for S67 low threshold for S67115)

• Profile S70830 (additional profile for connection of hinged system S77 with sliding system S700) added on profiles index and profiles 1:1 chapters

• External sliding sash stopper added on the chapter of accessories code 6606252102 (white RAL 9016), code 6606252103 (black RAL 9005) και code 6606252109 (silver RAL 9006)

• Flyscreen handle with adhesive tape code 610-00-701-33 (natural anodized 101020) and 610-00-701-45 (black anodized 103520) replaced the previous code 610-00-862-00 in typologies and added on the accessories chapter.